CBR 650 R Modified



CBR 650 R Modified







modified cbr 650f,150,650



CBR 650 R Accessories

Installing accessories for your Honda CBR 650 to extract more power and better performance can be done in a variety of ways, or if your just looking to modify the look of your Honda CBR 650 there are abundant accessories to go about it.

CBR 650 R accessories that are normally installed involve installing a better flowing exhaust system to increase the velocity of the exhaust gases. A correctly tuned Honda CBR 650 exhaust system will give better performance usually in the mid to top end range of power. This gives the Honda CBR 650 better acceleration and a higher top speed. The original exhaust system is also very heavy and with a well built high quality CBR 650 exhaust system the weight will be reduced dramatically and weigh not even a 1/4 of the factory exhaust. The weight reduction will also contribute to better acceleration and handling characteristics of the Honda CBR 650. Aftermarket CBR 650 exhaust accessories are usually a bit louder than stock systems, but not unbearable unless it is a full on Honda CBR 650 racing exhaust system. For racing exhaust designed for the CBR 650 which may possibly be used on the street from time to time a 'DB Killer' is usually sold or included with the exhaust system.

A DB killer is installed in the rear of the Honda CBR 650 exhaust at the exit hole of the muffler. It usually resembles a small plug with holes in it which reduce noise levels and serve to constrict minimally. When a DB Killer is installed the performance of a Honda CBR 650 performance exhaust system usually loses the smallest bit of velocity in order to reduce noise levels.


CBR 650 R Air Filter Accessories

CBR 650 R air filter accessories can help improve performance. A better flowing air filter for the Honda CBR 650 allows more air into the combustion chamber allowing the bike to create more power. Not only this but a freer flowing air filter for the Honda CBR 650 allows the piston to draw air into the cylinder with less effort and allows the bike to reach higher RPM's at a faster rate. More air in equals more power, so for the best results an exhaust system for the Honda CBR 650 should also be used in conjuction with a high performance air filter for the best performance.



CBR 650 R ECU Accessories

Honda CBR 650 ECU accessories involve installing an aftermarket piece of electronics which allows the fuel to air ratio to be adjusted. The ignition timing maps may also be adjusted to compensate for the various ratios. In some aftermarket ECU electronics for the Honda CBR 650 trimming of the fuel injectors is also possible which allows further fuel adjustments. It is recommended to use a performance ECU when installing an aftermarket exhaust for the Honda CBR 650 although it is not mandatory since ECU's can usually swing +/- 20%. But to extract the absolute best performance from a racing exhaust for the Honda CBR 650 as well as free flow air filter, an adjustable ECU for the Honda CBR 650 is the ticket for the best possible performance.


CBR 650 R Handling Accessories - Tires

While the Honda CBR 650 tires are better equipped than it's little brother the CBR 250. A better set of stickier tires with a more useable radius may be desireable. A tire with a rounder profile will allow the Honda CBR 650 to take corners at a more stable angle as well decrease rolling resistance with the correct rubber compound. Wet weather traction may also be improved over the original Honda CBR 650 tires. Braking distance will also be decreased with a better chance of the tires not losing their grip during quick unexpected heavy braking conditions. A good set of tires are probably one of the best modifications you can make to the Honda CBR 650, it will allow you to ride to your fullest potential with confidence without having to worry about the bike sliding out from underneath you. Not only this but once you become confident with the tires and know it's limits, riding will take on a whole new meaning as you tackle corners at speeds and lean angles you never would've imagined you could with the original tires on the Honda CBR 650. This one modification will truly help to make you a better more confident rider.


CBR 650 R Rearset Accessories

You'll probably be considering CBR 650 rearset accessories when you start to get your lean on and put your knee down, you're going to start finding that yor footpegs are starting to scrape the concrete the more you lean over. While rearsets will allow you to take corners without scraping and also give the Honda CBR 650 a more agressive riding position, they can be uncomfortable for use in normal day to day riding and feel rather cramped. Although if you don't mind CBR 650 rearset accessories, these will make the riding position more aggressive and give better control of the bike when riding fast and hard. CBR 650 rearset accessories will put the feet up higher and farther back and change the bikes center of gravity with the rider on it. Rearsets will allow you to pitch into corners at a more controlled rate and will shift the weight of the rider forward a bit which aids in front wheel traction.


CBR 650 R Windshield Accessories

When riding at high speeds doing a CBR 650 windshield accessory modification is a great thing to do. An aftermarket windshield can help in a few ways, it can help lift the oncoming air up and over the rider allowing the rider to ride with less crouching to avoid wind resistance. A Honda CBR 650 windshield accessory modification can aso provide better stability and quicker turning as the bike cuts through the air. The faster you go the more wind resistance there will be and at 50 mph, it takes approximately 5hp alone to overcome the wind resistance. Accessory windshields for the Honda CBR 650 usually come in three types, the double bubble which can be close to original height but cuts the air better, a sportier windshield that is slightly higher to keep a little bit more wind off the rider, and touring type windshields that are usually substantially taller than the factory height. The touring windshields available for the Honda CBR 650 usually allow the rider to sit almost totally upright to avoid wind resistance, but at the expense of looking a little goofy in the process.


CBR 650 R Seat Accessories

Taking a long ride can take a toll on your buttocks and a Honda CBR 650 seat accessory can be the solution you are looking for. But be aware that changing the seating position can also have an affect on how the bike handles if the height of the seat is reduced or increased. If a change of the Honda CBR 650 seat height is involved it may change the center of gravity and throw the handling off from the original seat height. You will have to relearn how the CBR 650 handles and compensate for any changes in balance that a different seat height may induce on the Honda CBR 650 and the rider.

Honda CBR 650 seats can be made out of a variety of materials ranging from real leather and vinyl to cloth materials that prevent sliding. Sliding and easy mobility may be desired though, especially when riding on a track or twisty mountain roads where shifting weight to take turns is paramount to fast riding techniques. A vast array of different types of foam can be used to provide support and comfort in an aftermarket seat for the Honda CBR 650, there are foams that are supportive for long rides that you virtually melt into and there are firmer foams that allow you to shift weight from side to side easier. There are even gel type seats that have good shock absorbtion. The width of the seat also has an affect on the seat height, a wider seat usually makes the ride height even higher because it spreads the seating area farther apart and lifting the legs.